bandeau Hero recherche

Publications

2016

Articles avec comité de lecture

 Aubry J., Barbedette B., Assessment of the interest of series hybridisation for a human-powered vehicle. Electric pedal generator pre-sizing, European journal of Electrical Engineering, Accepté

Hassar M., Lascoup B., Aboura Z., Benzeggagh M.L., Effet des nanoparticules de noir de carbone sur l'efficacité de blindage électromagnétique des composites, Matériaux et Techniques, Accepté

Kovaltchouk T., Audoux K., Rouland S., Aubry J., Ben Ahmed H. et al., Power smoothing of a direct wave energy converter : management and sizing of a supercapacitor, European journal of Electrical Engineering, Accepté

Mesbahi T., Khenfri F., Rizoug N., Bartholomeus P., Lemoigne P., Dynamical modeling of Li-ion batteries for electric vehicle applications based on hybrid particle Swarm-Nelder-Mead (PSO-NM) optimization algorithm, Electric power systems research, Accepté

Murzyn F., Mehel A., Influence of the virtual origin on the turbulent length scales in the grid-generated turbulence, International Journal of Fluid Mechanics Research, Vol. 43 N° 1, p. 62-78, 2016

Ouddah N., Boukhnifer M., Chaïbet A., Monmasson E., Fixed structure H-infinity loop shaping control of switched reluctance motor for electrical vehicle, Transaction of IMACS on Mathematics and Computers in Simulation, Accepté, disponible en ligne

Raisemche A., Boukhnifer M., Diallo D., New fault-tolerant control architectures based on voting algorithms for electric vehicle induction motor drive, Transactions of the Institute of Measurement and Control, Accepté, en impression

Wang H., Murzyn F., Experimental assessment of characteristic turbulent scales in two-phase flow of hydraulic jump : from bottom to free surface, Environmental Fluid Mechanics, p. 1-19, 08/04/2016, Publié en ligne

Yacef F., Bouhali O., Hamerlain M., Rizoug N., Observer-based adaptive fuzzy backstepping tracking control of quadrotor unmanned aerial vehicle powered by Li-ion battery, Journal of Intelligent & Robotic Systems, p. 1-19

Communications internationales

Godot J., Saudrais S., Alif A., Barbedette B., Larouci C., Safety analysis generation from prototyping models for transportation systems, SAC 2016, 31st ACM Symposium on Applied Computing, 04-08/04/2016, Pise, Italie

Khammassi M., Marimbordes T., Aubry J., Barbedette B., Cormerais M., Larouci C., Frossard Q., A multi-physical model of an active thermal management valve with experimental validation, SAE 2016 World Congress, 12-14/04/2016, Detroit, USA

Mehel A., Murzyn F., Rodriguez R., The interactions of the exhaust ultrafine particle with the vehicle near-wake flow, 21th International Transport and Air Pollution Conference, 24-26/05/2016, Lyon, France

Monti A., El Mahi A., Jendli Z., Guillaumat L., Vibration behavior of a lightweight bio-based sandwich structure, ICCS19 19th International Conference on Composite Structures, 05-09/09/2016, Porto, Portugal

Autres

Rodriguez R., Murzyn F., Mehel A., Larrarte F., Experimental study of nanoparticle dispersion in the wake of a vehicle model and their infiltration into passenger compartment, Ecole de Physique des Houches, 2016, Les Houches, France

2015

Articles avec comité de lecture

 Azib T., Bendali M., Larouci C., Hemsas K.E., Fault tolerant control of interleaved buck converter for automotive application, International Review of Electrical Engineering (IREE), Vol. 10 N° 3, 05-06/2015

Bendali M., Larouci C., Azib T., Marchand C., Coquery G., Design methodology of an interleaved buck converter for onboard automotive application, multi-objective optimization under multi-physic constraints, IET Electrical Systems in Transportation, Vol. 5 n°2, p. 53-60, 06/2015

Mehel A., Murzyn F., Effect of air velocity on nanoparticles dispersion in the wake of a vehicle model : wind tunnel experiments, Atmospheric pollution research, N°6, p. 612-617

Oubellil R., Boukhnifer M., Fault tolerant control of energy management system for an electrical vehicle, Electromotion Journal, Vol. 22, p. 25-34

Soubra H., Abran A., Sehit M., Software functional size measurement for processor load estimation in AUTOSAR, Software Measurement, Lecture Notes in Business Information Processing, Vol. 230, p. 114-129

Soubra H., Jacot L., Lemaire S., Manual and automated functional size measurement of an aerospace real-time embedded system : a case study based on Scade and on Cosmic ISO 19761, International Journal of Engineering Research and Science Technology IJERST, Vol. 4 n°2, p. 79-100, 05/2015

Wang H., Murzyn F., Chanson H., Interaction between free-surface, two-phase flow and total pressure in hydraulic jumps, Experimental Thermal and Fluid Science, Vol. 64, p. 30-41, 2015

 

Communications internationales

Hammoudi M.Y., Benbouzid M., Rizoug N., Allag A., New state observer based on Takai-Sugeno fuzzy controller of induction motor, IEEE ICSC 2015, 7-9/02/2015, Anaheim, USA

Khenfri F., Chaaban K., Chetto M., A novel heuristic method for mapping AUTOSAR runnables to tasks, PECCS 2015 5th International Conference on Pervasive and Embedded Computing and Communication Systems, 11-13/02/2015, Angers, France, Best paper Award PECCS 2015

Khenfri F., Chaaban K., Chetto M., A holistic optimization approach for the synthesis of AUTOSAR E/E architecture, 30th ACM / SIGAPP Symposium on Applied Computing - SRC session, 13-17/04/2015, Salamanque, Espagne

Kovaltchouk T., Ben Ahmed H., Multon B., Aubry J., Venet P., An aging-aware life cycle cost comparison between supercapacitors and Li-ion batteries to smooth direct wave energy converter production, IEEE Powertech 2015, 29-06/02-07/2015, Eindhoven, Pays-Bas

Kovaltchouk T., Blavette A., Ben Ahmed H., Multon B., Aubry J., Comparison between centralized and decentralized storage energy management for direct wave energy converter farm, Tenth International Conference on Ecological Vehicles and Renewable Energies EVER 2015, 31/03-02/04/2015, Monte Carlo, Monaco

Kovaltchouk T., Rongère F., Primot M., Aubry J., Ben Ahmed H., Multon B., Model predictive control of a direct wave energy converter constrained by the electrical chain using an energetic approach, 11 th European Wave and Tidal Energy Conference EWTEC 2015, 6-11/09/2015, Nantes, France

Lebaupin Y., Chauvin M., Truong Hoang T.Q., Touchard F., Beigbeder A., Flax fiber reinforced polyamide 11 composite : influence of constituents and process parameters, ICNF 2015 International Conference on Natural Fibers, 27-09/03/2015, Sao Miguel, Açores, Portugal

Leserf P., de Saqui Sannes P., Hugues J., Multi domain optimization with SysML modeling, EFTA 2015, 20th IEEE International Conference on Emerging Technologies and Factory Automation, 8-11/09/2015, Luxembourg, Luxembourg

Leserf P., de Saqui-Sannes P., Hugues J., Chaaban K., SYSML modeling for embedded systems design optimization : a case study, Modelsward 2015 3rd International Conference on Model-driven Engineering and Software Development, 9-11/02/2015, Angers, France

Mehel A., Murzyn F., Correlation between ultrafine particle dispersion ans mean and turbulent flow structure in th near-wake of a vehicle, FLUCOME 2015, 13th International Symposium on Fluid Control, Measurement and Visualization, 15-18/11/2015, Doha, Qatar

Ouddah N., Loukkas N., Chaïbet A., Boukhnifer M., Monmasson E., Experimental evaluation of second sliding modes observer and extended Kalman filter in a sensorless robust control of switched reluctance motor for EV application, 23th Mediterranean Conference on Control and Automation MED2015, 16-19/06/2015, Torremolinos, Espagne

Rkhissi-Kammoun Y., Ghommam J., Boukhnifer M., Mnif F., RISE-backstepping feedback control for induction machine in electric vehicle applications, 23th Mediterranean Conference on Control and Automation MED2015, 16-19/06/2015, Torremolinos, Espagne

Saidi S. E., Cotard S., Chaaban K., Marteil K., An ILP approach for mapping AUTOSAR runnables on multi-core architectures, 7th Workshop on Rapid Simulation and Performance Evaluation : Methods and Tools, 19-21/01/2015, Amsterdam, Pays-Bas

Saidi S.E., Cotard S., Chaaban K., Marteil K., An ILP approach for mapping AUTOSAR runnables on multi-core architectures, RAPIDO'15 Proceedings of the 2015 Workshop on Rapid Simulation and Performance Evaluation : Methods and Tools, Article 6, 21/01/2015, Amsterdam, Pays-Bas

Soubra H., Abran A., Sehit M., Functional Size Measurement for Processor Load Estimation in AUTOSAR, IWSM Mensura 2015, 5-7/10/2015, Cracovie, Pologne

aUtRES

Lebaupin Y., Chauvin M., Truong Hoang T.Q., Touchard F., Beigbeder A., Optimisation des propriétés microstructurales et mécaniques d'un composite lin / polyamide 11, 19èmes Journées Nationales sur les Composites JNC 2015, 29/06-01/07/2015, Villeurbanne, France

Leserf P., de Saqui-Sannes P., Hugues J., Chaaban K., Architecture optimization with SysML modeling : a case study using variability, CCIS - Communications in Computer and Information Science, Springer Verlag, p. 1-16

Loulou H., Saudrais S., Soubra H., Larouci C., Efficiency monitoring dynamic data-streams in smart cities, CIEL 2015, 4ème conférence en Ingénierie du logiciel, 09-11/06/2015, Bordeaux, France

Mehel A., Murzyn F., Characterization of ultrafine pollutant dispersion downstream of a car, Workshop sur la dépollution moteur, Pôle de Compétitivité Mov'eo, 21/04/2015, Caen, France

Mehel A., Murzyn F., Experimental study of ultrafine pollutant dispersion downstream of a car, CERTAM Workshop, Characterization of complex nanoaerosol emissions : metrology, health and environmental issues, 24-25/03/2015, Rouen, France

Monti A., El Mahi A., Guillaumat L., Jendli Z., Elaboration et étude d'une structure sandwich bio-sourcée : des constituants à la structure, 19èmes Journées Nationales sur les Composites JNC 2015, 29/06-01/07/2015, Villeurbanne, France

Monti A., El Mahi A., Guillaumat L., Jendli Z., Analyse de l'endommagement d'un composite à matrice thermoplastique renforcée de fibres de lin par émission acoustique, 22ème Congrès Français de Mécanique, 24-28/08/2015, Lyon, France

Zouari S., Genevaux J-M., Brocail J., Ablitzer F., Formation of band gaps in thin plate with a periodic array of resonators, 22ème Congrès Français de Mécanique, 24-28/08/2015, Lyon, France

2014

Articles avec comité de lecture

Aouaouda S., Chadli M., Boukhnifer M., Karimi H.R., Robust fault tolerant tracking controller design for vehicle dynamics : a descriptor approach, Mechatronics, 2014

Azib T., Hemsas K.E., Larouci C., Energy management and control strategy of hybrid energy storage system for fuel cell power sources, International Review on Modelling and Simulations (IREMOS), Vol. 7 N° 6, 06/2014

Azib T., Larouci C., Chaïbet A., Boukhnifer M., On-line energy management strategy of a hybrid fuel cell / battery / ultracapacitor vehicular power system, IEEJ Transactions on Industry Applications, Vol. 9 N° 5, p. 548-554, 09/2014

Boudjedir H., Bouhali O., Rizoug N., Adaptive neural network control based on neural observer for quadrotor unmanned aerial vehicle, Advanced Robotics Journal, Vol. 28 N° 17, p. 1151-1164, 2014

Bouhali O., Francois B., Rizoug N., Equivalent matrix structure modelling and control of a three-phase flying capacitor multilevel inverter, IET Power Electronics, Vol. 7 N° 7, p. 1787-1796, 07/2014

Bouhali O., François B., Rizoug N., Line to line voltage space vector modulation for neutral-point clamped multi-level converter with DC-link capacitor voltage balancing using redundant vectors, Electric power components and Systems, Vol. 42 n° 10, 07/2014

Boukhnifer M., Chaïbet A., Robust control of aerial vehicle flight : simulation and experimental results, IEEE Aerospace and Electronic Systems Magazine, Vol. 29 n° 9, p. 4-12, 09/2014

Kovaltchouk T., Multon B., Ben Ahmed H., Aubry J., Venet P., Enhanced aging model for supercapacitors taking into account power cycling: application to the sizing of an energy storage system in a direct wave energy converter, IEEE Transactions on Industry Applications, N° 99, 11/2014

Le Mercier K., Watremez M., Brocail J., Dubar L., Evolution of dynamic recrystallization of aisi-1045 steel under critical friction conditions, Advanced Materials Research, Vol. 966-967, p. 168-174, 2014

Mesbahi T., Ouari A., Ghennam T., Berkouk E.M., Rizoug N., Mesbahi N., Meradji M., A stand-alone wind power supply with a li-ion battery energy storage system, Renewable and Sustainable Energy Reviews, Vol. 40, p. 204-213, 12/2014

Raisemche A., Boukhnifer M., Larouci C., Diallo D., Two active fault tolerant control schemes of induction motor drive in EV or HEV, IEEE Transactions on Vehicular Technology, Vol. 63 N°1, p. 19-29, 01/2014

Sadoun R., Rizoug N., Bartholomeüs P., Le Moigne P., Optimal sizing of hybrid supply for electric vehicle using li-ion battery and supercapacitor, International Review of Electrical Engineering, Vol. 9 N° 2, 04/2014

Senecaut Y., Watremez M., Brocail J., Dubar L., Identification of friction law to model orthogonal cutting, Key Engineering Materials, Vol. 611-612, p. 1194-1201, 2014

Soubra H., Ebert C., Functional size estimation technologies for software maintenance, IEEE Software, Vol. 31 N° 6, p. 24-29, 11-12/2014

Wang H., Murzyn F., Chanson H., Total pressure fluctuations and two-phase flow turbulence in hydraulic jumps, Experiments in Fluids, Vol. 55 Art. 1847, 11/2014

Communications internationales

Ait Ali Yahia L., Gehin E., Sagot B., A new device for the measurement of soot aggregates thermophoretic velocity, International Aerosol Conference, 31-08/05-09/2014, Busan, Corée du Sud

Ait Ali Yahia L., Gehin E., Sagot B., Tri-thermal device sizing for thermophoresis deposition measurements of nanoparticle soot aggregates, 10th International Conference on Heat Transfer, Fluid Mechanics and Thermodynamics (HEFAT2014), 14-16/07/2014, Orlando, USA

Aouaouda S., Boukhnifer M., Observer based fault tolerant controller design for induction motor drive in EV, IEEE CCA International Multi-Conference on Systems and Control, 08-10/10/2014, Nice - Antibes, France

Aouaouda S., Boukhnifer M., Bouhali O., Sensor fault observer design for uncertain nonlinear systems, 23rd IEEE ISIE 2014, 01-04/06/2014, Istanbul, Turquie

Bendali M., Larouci C., Azib T., Coquery G., Marchand M., Reliability assessment in the design of interleaved converters under multi-physical constraints, 23rd IEEE ISIE 2014, 01-04/06/2014, Istanbul, Turquie

Bendali M., Larouci C., Azib T., Marchand C., Coquery G., Design with optimization of an interleaved buck converter for automotive application ; Effect of the EMC constraint, 7th IET International Conference on Power Electronics, Machines and Drives, 08-10/04/2014, Manchester, Royaume-Uni

Bouhali O., Rizoug N., Mesbahi T., Francois B., Modeling and control of the three-phase NPC multilevel converter using an equivalent matrix structure, 7th IET International Conference on Power Electronics, Machines and Drives (PEMD 2014), 08-10/04/2014, Manchester, Royaume-Uni

Chabir A., Boukhnifer M., Bouteraa Y., Ghommam J., Fixed order robust H-infinity controller for 3-DOF helicopter, 11th IEEE Electrimacs, 19-22/05/2014, Valence, Espagne

Chaïbet A., Boukhnifer M., Experimental second order sliding mode fault tolerant control for moment gyroscope system with sensor fault, IEEE CoDIT'14 International Conference on Control, Decision and Information Technologies, 03-05/11/2014, Metz, France

Estival P., Krebs G., Marchand C., Sehab R., Barbedette B., Pre-sizing of permanent magnet synchronous machine under mass constraints, 6th International Conference on Recent Advances in Aerospace Actuation Systems and Components R3ASC 2014, 2-3/04/2014, Toulouse, France

Hassar M., Walrick J-C., Gillet S., Benzeggagh M., Contribution to the improvement of shielding effectiveness of composite materials, ECCM16 16th European Conference on Composite Materials, 22-26/06/2014, Séville, Espagne

Jendli Z., Walrick J-C., Bocquet M., Fitoussi J., Strain rate effects on the mechanical behavior of carbon-thermoplastic matrix woven composites, ECCM16 16th European Conference on Composite Materials, 22-26/06/2014, Séville, Espagne

Kovaltchouk T., Aubry J., Multon B., Ben Ahmed H., Venet P., Enhanced aging model for supercapacitors taking into account power cycling : application to the sizing of an energy storage system in a direct wave energy converter, 9th International Conference on Ecological Vehicles and Renewable Energies (EVER) 2014, 23-27/03/2014, Monte-Carlo, Monaco, Best paper on Renewable Energy

Le Mercier K., Watremez M., Brocail J., Dubar L., Evolution of dynamic recrystallization of aisi-1045 steel under critical friction conditions, 6th International Conference on Tribology in Manufacturing Processes & Joining by Plastic Deformation (ICTMP 2014), 22-24/06/2014, Darmstadt, Allemagne

Mehel A., Murzyn F., The influence of the vehicle near-wake on the exhausted ultrafine particle dispersion, Aerosol Technology 2014, 16-18/06/2014, Karlsruhe, Allemagne

Mesbahi T., Rizoug N., Bartholomeüs P., Le Moigne P., Improved model of battery / supercapacitor hybrid energy storage system based on thermo-electrical and aging behaviors, 7th IET International Conference on Power Electronics, Machines and Drives, 08-10/04/2014, Manchester, Royaume-Uni

Mesbahi T., Rizoug N., Bartholomeüs P., Le Moigne P., A new energy management strategy of a battery / supercapacitor hybrid energy storage system for electric vehicular applications, 7th IET International Conference on Power Electronics, Machines and Drives, 08-10/04/2014, Manchester, Royaume-Uni

Oubellil R., Boukhnifer M., Passive fault tolerant control design of energy management system for electric vehicle, 23rd IEEE ISIE 2014, 01-04/06/2014, Istanbul, Turquie

Ouddah N., Boukhnifer M., Chaïbet A., Monmasson E., Fixed structure H-infinity loop shaping control of switched reluctance motor for electrical vehicle, 11th IEEE Electrimacs, 19-22/05/2014, Valence, Espagne

Ouddah N., Boukhnifer M., Chaïbet A., Monmasson E., Robust LPV current control of switched reluctance motors, 22nd Mediterranean Conference on Control and Automation, 16-19/06/2014, Palerme, Italie

Ouddah N., Boukhnifer M., Chaïbet A., Monmasson E., Robust controller designs of switched reluctance motor for electrical vehicle, 22nd Mediterranean Conference on Control and Automation, 16-19/06/2014, Palerme, Italie

Ouddah N., Boukhnifer M., Chaïbet A., Monmasson E., Berthelot E., Experimental robust H-infinity controller design of switched reluctance motor for electrical vehicle system, IEEE CCA International Multi-Conference on Systems and Control, 08-10/10/2014, Nice - Antibes, France

Raisemche A., Boukhnifer M., Larouci C., Diallo D., Experimental GIMC fault tolerant control using fixed order H infinity approach for EV induction motor drive, 22nd Mediterranean Conference on Control and Automation, 16-19/06/2014, Palerme, Italie

Rizoug N., Feld G., Bouhali O., Mesbahi T., Micro-hybrid vehicle supplied by a multi-source storage system (battery and supercapacitors): optimal power management, 7th IET International Conference on Power Electronics, Machines and Drives (PEMD 2014), 08-10/04/2014, Manchester, Royaume-Uni

Rizoug N., Mesbahi T., Bartholomeüs P., Le Moigne P., Micro-hybrid vehicle supplied by a multi-source storage system (battery and supercapacitors) : experimental tests, 7th IET International Conference on Power Electronics, Machines and Drives, 08-10/04/2014, Manchester, Royaume-Uni

Sagot B., Forthomme A., Wojda M., De La Bourdonnaye G., Tuning of an oil mist generator for the performance evaluation of oil separators used in blow-by applications, Fluid-Particle Separation 2014 (FPS 2014), 15-17/10/2014, Lyon, France

Senecaut Y., Watremez M., Brocail J., Dubar L., Identification of friction law to model orthogonal cutting, 17th Annual Conference on Material Forming (ESAFORM 2014), 07-09/06/2014, Espoo, Finlande

Soubra H., Abran A., Ramdane-Cherif A., Verifying the accuracy of automation tools for the measurement of software with COSMIC - ISO 19761, International Workshop on Software Measurement and the International Conference on
Software Process and Product Measurement, 6-8/10/2014, Rotterdam, Pays-Bas
Soubra H., Ebert C., Managing software projects with COSMIC, Metrikon 2014, 6-7/11/2014, Stuttgart, Allemagne

Tchakaloff B., Saudrais S., Babau J-P., Efficient models configuration for an electric vehicle energy management software, SEAA 2014 Euromicro Conference Series on Software Engineering and Advanced Applications, 27-29/08/2014, Verone, Italie

Tchakaloff B., Saudrais S., Babau J-P., Integration of physical models in the ORQA framework for electric vehicle energy management, WCOP'14 19 International doctoral Symposium on Components and Architecture, p. 7-12, 30/06/2014, Lille, France

Wang H., Murzyn F., Chanson H., Pressure fluctuations and air-water flow properties in hydraulic jumps, ydraulic Structures and Society, Engineering Challenges and Extremes, Proceedings of the 5th IAHR International Symposium on Hydraulic Structures ISHS 2014, 25-27/06/2014

Younsi M.O., Bendali M., Azib T., Larouci C., Marchand C., Coquery G., FTC and current-sharing control techniques for interleaved buck converter in automotive application, 7th IET International Conference on Power Electronics, Machines and Drives, 08-10/04/2014, Manchester, Royaume-Uni

Zouari S., Brocail J., Genevaux J-M., Ablitzer F., Damping wave propagation in periodic composite panels, 19th Conference Vibrations, Shocks and Noise (VISHNO 2014), 17-19/06/2014, Aix-en-Provence, France

 

Autres

 Ait Ali Yahia L., Gehin E., Sagot B., Mesure de la vitesse de thermophorèse d'agrégats de suies : dimensionnement d'un dispositif de dépôt tri-therme, CFA 2014, 29ème Congrès Français sur les Aérosols, 22-23/01/2014, Paris, France

Aubry J., Azib T., Chaaban K., Gillet S., Lefeuve J., Mehel A., Murzyn F., Saudrais S., Sehab R., L'initiation des étudiants au domaine de la recherche en école d'ingénieurs : l'exemple des projets PIRATE à l'ESTACA, Revue 3EI, N° 76, 2014

Aubry J., Barbedette B., Evaluation de l'intérêt d'une hybridation série pour un véhicule à propulsion humaine : pré-dimensionnement d'une génératrice-pédalier, SGE Symposium de Génie Electrique SGE'14, 08-10/07/2014, Cachan, France

Bendali M., Larouci C., Azib T., Marchand C., Coquery G., Intégration de la fiabilité dans la conception sous contraintes multi-physiques des convertisseurs statiques multicellulaires, SGE Symposium de Génie Electrique SGE'14, 08-10/07/2014, Cachan, France

Boukhnifer M., Azib T., Chaïbet A., Larouci C., Commande et gestion d'énergie d'une chaine de conversion pour véhicule électrique, Revue 3EI, N° 74, 01/2014

Estival P., Krebs G., Marchand C., Sehab R., Barbedette B., Pré-dimensionnement d'une machine synchrone à aimants permanents en quasi statique validé par un modèle dynamique, SGE Symposium de Génie Electrique SGE'14, 08-10/07/2014, Cachan, France

Jendli Z., Fitoussi J., Walrick J-C., Etudes du comportement endommageable de composites thermoplastiques en dynamique rapide, Matériaux 2014, 24-28/11/2014, Montpellier, France

Kovaltchouk T., Audoux K., Rouland S., Aubry J., Ben Ahmed H., Multon B., Lissage d'une production houlogénérée : gestion et dimensionnement d'un système de stockage par supercondensateurs sous contrainte de flicker, SGE Symposium de Génie Electrique SGE'14, 08-10/07/2014, Cachan, France

Lebaupin Y., Truong Hoang T.Q., Chauvin M., Touchard F., Beigbeder A., Influence des paramètres de mise en œuvre sur les propriétés microstructurales et mécaniques d'un composite unidirectionnel lin / polyamide 11 (poster), Mecamat 2014, 20-24/01/2014, Aussois, France

Mesbahi T., Rizoug N., Bartholomeüs P., Le Moigne P., Prise en compte du vieillissement pour la modélisation d'une source hybride batterie / supercondensateur, SGE Symposium de Génie Electrique SGE'14, 08-09/07/2014, Cachan, France

Murzyn F., Mehel A., Contribution expérimentale à l'étude de la dispersion de polluants particulaires : application au domaine automobile, Fête de la Science, 2014, Laval, France

Tchakaloff B., Saudrais S., Babau J.P., ORQA : modélisation de l'énergie et de la qualité de service, 3ème Conférence en Ingénierie du Logiciel CIEL 2014, 10-12/06/2014, Paris, France

Vacossin B., Bedrici N., Gatignol P., Interaction entre un faisceau ultrasonore et une structure à deux couches, 12ème Congrès Français d'Acoustique, 22-25/05/2014, Poitiers, France

Wang H., Murzyn F., Chanson H., Pressure, turbulence and two-phase flow measurements in hydraulic jumps, University of Queensland, Report CH95/14, 2014

Zouari S., Brocail J., Genevaux J-M., Ablitzer F., Amortissement des matériaux composites par effet réseau, JST AMAC 2014, 04/2014, Nevers, France

 

2013

Articles avec comité de lecture

Boukhnifer M., Ferreira A., Fault tolerant control of a teleoperated piezoelectric microgripper, Asian Journal of Control, Vol. 15 n°4, p. 888-900, 05/2013

Guerich M., Assaf S., Optimization of noise transmission through sandwich structures, Journal of Vibration and Acoustics, Vol. 135 N°5, 18/06/2013

Larouci C., Azib T., Boukhnifer M., Chaïbet A., Influence of the control mode on the design of a power factor correction flyback converter, IEEJ Transactions on Electrical and Electronic Engineering, 2013

Larouci C., Azib T., Chaïbet A., Boukhnifer M., Control of a flyback converter in a mixed conduction mode; influence of the converter design using optimization under constraints, IEEJ transactions on industry applications, Vol. 2 n° 3, p. 132-140, 2013

Lascoup B., Perez L., Autrique L., Crinière A., On the feasability of defect detection in composite material based on thermal periodic excitation, Composites Part B, Vol. 45 N° 1, p. 1023-1030, 02/2013

Ledoux C., Lefranc P., Larouci C., Pre-sizing methodology of DC-AC converters using a virtual prototyping tool applied to sequential multi-load systems, IET Power Electronics Journal, Vol. 6 n° 2, 02/2013

Ledoux C., Lefranc P., Larouci C., Pre-sizing methodology of embedded static converters using optimisation under constraints ; comparison of two power sharing topologies, IET Electrical Systems in Transportation Journal, Vol. 3 n° 1, p. 1-9, 03/2013

Raisemche A., Boukhnifer M., Larouci C., Diallo D., Commande tolérante aux défauts du capteur mécanique d'une machine asynchrone dans une chaine de traction d'un véhicule électrique, Revue 3EI, N° 73, p. 39-45, 07/2013

Sagot B., Thermophoresis for spherical particles, Journal of Aerosol Sciences, Vol. 65, p. 10-20, 11/2013

Tabbache B., Rizoug N., Benbouzid M.E.H., Kheloui A., A control reconfiguration strategy for post-sensor FTC in induction motor-based Evs, IEEE Transactions on Vehicular Technology, Vol. 62 N°3, p. 965-971, 03/2013

Tcheukam-Toko D., Mokem-Chetchueng M., Mouangue R., Beda T., Murzyn F., Characterization of hydraulic jump over an obstacle in an open-channel flow, International Journal of Hydraulic Engineering, Vol. 2 n° 5, p. 71-84, 2013

Truong Hoang T.Q., Touchard F., Non-woven flax fiber reinforced polypropylene: mechanical properties in static and low velocity impact behaviours, Polymers & Polymer Composites, Vol. 21 N° 5, 2013

Zhang Y., Abraham O., Tournat V., Le Duff A., Lascoup B., Loukili A., Grondin F., Durand O., Validation of a thermal bias control technique for CODA wave interferometry (CWI), Ultrasonics, Vol. 53 N° 3, p. 658-664, 31/03/2013

Zhang Y., Tournat V., Abraham O., Durand O., Letourneur S., Le Duff A., Lascoup B., Nonlinear mixing of ultrasonic coda waves with lower frequency-swept pump waves for a global detection of defects in multiple scattering media, Journal of Applied Physics, Vol. 113 N° 6, p. 064905-064905-8, 02/2013

 

Communications internationales

Bedrici N., Bentahar M., Gatignol P., Boundary element method (BEM) and Fourier integral, application to the interaction of Lamb waves with a defect located in a plate, 13th International Symposium on Nondestructive Characterization of Materials, 20-24/05/2013, Le Mans, France

Bendali M., Larouci C., Azib T., Marchand C., Coquery G., Design of interleaved power converters under volume, efficiency and thermal constraints (poster), PCIM 2013, 12-14/05/2013, Nuremberg, Allemagne

Bendali M., Larouci C., Azib T., Marchand C., Coquery G., Design methodology with optimization of an interleaved buck converter for automotive application, IEEE Eurocon 2013, 1-4/07/2013, Zagreb, Croatie

Boukhnifer M., Raisemche A., Diallo D., Fault tolerant control design of induction motor drive in electrical vehicle: a hybrid control approach, 21st Mediterranean Conference on Control and Automation, p. 40-45, 25-28/06/2013, Platanias-Chania, Grèce

Boukhnifer M., Raisemche A., Diallo D., Larouci C., Fault tolerant control to mechanical sensor failures for induction motor drive : a comparative study of voting algorithms, 39th IEEE IECON, 10-13/11/2013, Vienne, Autriche

Chaïbet A., Boukhnifer M., Experimental passive fault tolerant control for gyroscope system, 21st IEEE Mediterranean Conference on Control and Automation, p. 167-172, 25-28/06/2013, Platanias-Chania, Grèce

Guerich M., Assaf S., Design vibro-acoustic optimization of sandwich panels, Internoise 2013, 15-18/09/2013, Innsbrück, Autriche

Kovaltchouk T., Aubry J., Multon B., Ahmed H.B., Influence of IGBT current rating on the thermal cycling lifetime of a power electronic active rectifier in a direct wave energy converter, 15th European Conference on Power Electronics and Applications EPE, 03-05/09/2013, Lille, France

Kovaltchouk T., Multon B., Ben Hamed H., Aubry J., Rongère F., Glumineau A., Influence of control strategy on the global efficiency of a direct wave energy converter with electric power take-off, Ecological Vehicles and Renewable Energies (EVER) 8th International Conference and Exhibition, 27-30/03/2013, Monte Carlo, Monaco

Lau K.K., Stepan P., Tran C.M., Saudrais S., Tchakaloff B., A holistic (component-based) approach to Autosar designs, 39th Euromicro Conference on Software Engineering and Advanced Applications SEAA 2013, 04-06/09/2013, Santander, Espagne

Mehel A., Comparison of nanoparticles deposition in turbulent flows using electrophoresis and two different charging mechanisms, Proceedings of the 11th International Conference of Numerical Analysis and Applied Mathematics, 23-25/09/2013, Rhodes, Grèce

Mesbahi T., Rizoug N., Bartholomeüs P., Le Moigne P., Li-ion battery emulator for electric vehicle applications, IEEE Vehicle Power and Propulsion Conference VPPC 2013, 15-18/10/2013, Pekin, Chine

Naimi S., Assaf S., Hamdi M.A., A numerical study to optimize a partially covered damping structure, Acoustics 2013, p. 1551-1556, 10-15/11/2013, New Delhi, Inde

Ouddah N., Boukhnifer M., Two control energy management schemes for electrical hybrid vehicle, 10th IEEE Multiconference on Systems, Signals and Devices SSD'2013, 18-21/03/2013, Hammamet, Tunisie

Rafa S., Khenfri F., Diaf S., Development and realization of an intelligent power strip for energy consumption management in hybrid wind / photovoltaïc systems, Energy procedia ; Proceedings of Mediterranean Green Energy Forum 2013, Vol. 42, p. 530-538, 2013

Rizoug N., Using of Aqueous or Organic Supercapacitor Technology in Hybrid and Electric Vehicle, EPE'13 ECCE, 03-05/09/2013, Lille, France

Sadoun R., Rizoug N., Bartholomeüs P., Le Moigne P., Optimal architecture of the hybrid source (battery / supercapacitor) supplying an electric vehicle according to the required autonomy, EPE 2013, 03-05/09/2013, Lille, France

Sagot B., Giardi J., Experimental study of the influence on cyclones collection efficiency of the particle load, 8th International Conference on Multiphase Flow, 26-31/05/2013, Séoul, Corée du Sud

Sagot B., Giardi J., Influence of the inlet particle diameter distribution on the experimental determination of cyclone collection efficiency, European Aerosol Conference, 01-06/09/2013, Prague, République Tchèque

Sehab R., Shanan T., Control laws for the emulation of an electric vehicle drivetrain by two elecric machines, IEEE Vehicle Power and Propulsion Conference VPPC 2013, 15-18/10/2013, Pekin, Chine

Soubra H., Fast functional size measurement with synchronous languages : an approach based on LUSTRE and on the Cosmic ISO 19761 Standard, Software Measurement and the 2013 Eighth International Conference on Software Process and Product Measurement (IWSM-MENSURA 2013), P. 3-8, 23-26/10/2013, Ankara, Turquie

Soubra H., Ebert C., Towards a method for specifying and estimating functional change in real-time embedded systems: a guideline based on COSMIC ISO 19761 with an AUTOSAR example, Metrikon 2013, 13-15/11/2013, Kaiserslautern, Allemagne

Tchakaloff B., Saudrais S., Babau J.P., ORQA: modeling energy and quality of service within Autosar models, Quality of Software Architecture (QOSA), 17-21/06/2013, Vancouver, Canada

Autres

Barbedette B., Aubry J., Comment préparer les futurs ingénieurs à la problématique de la mobilité des personnes handicapées, Colloque Vieillissement et Mobilité, 16/05/2013, Saint Quentin en Yvelines, France

Bedrici N., Vacossin B., Gatignol P., Générations d'ondes modales dans une structure multicouche plane par l'impact d'un faisceau ultrasonore, 21ème Congrès Français de Mécanique, 26-30/08/2013, Bordeaux, France

Berchet A., Simon B., Furgerot L., Beaudoin A., Rousseaux G., Chatellier L., Thomas L., Jarny S., Monnet S., Huberson S., Calluaud D., David L., Caplain B., Reungoat D., Chanson H., Glockner S., Lubin P., Murzyn F., Tessier B., Mouazé D., Processus hydro-sédimentaires du mascaret : modélisations physique et numérique, 14ème Congrès de l'Association des Sédimentologues de France, 04-05/11/2013, Paris, France

Hassar M., Gillet S., Walrick J-C., Benzeggagh M.L., Manufacturing optimization of nano-filled resin composites (poster), JNC18, 12-14/06/2013, Nantes, France

Hassar M., Walrick J-C., Gillet S., Benzeggagh M.L., Rousseau A., Influence de la dispersion des nano-charges de noir de carbone sur le comportement mécanique d'une résine thermodurcissable et suivi d'endommagement par émission acoustique, JNC18, 12-14/06/2013, Nantes, France

Jendli Z., Fitoussi J., Bocquet M., Walrick J-C., Comportement mécanique sous sollicitations rapides de composites tissés carbone à matrice thermoplastique, JNC18, 12-14/06/2013, Nantes, France

Jendli Z., Fitoussi J., Bocquet M., Walrick J-C., Caractérisation mécanique du comportement endommageable de composites thermoplastiques sous sollicitations rapides, MecaDymat 2013, 11-12/04/2013, Brest, France

Lascoup B., Recherche automatique de défaut à l'aide de sollicitations thermiques pulsées, JNC18, 12-14/06/2013, Nantes, France

Métoui S., Chauvin M., Guillaumat L., Lascoup B., Comportement mécanique et identification des mécanismes d'endommagement d'un composite à fibre de lin composé de couches de papier, JNC18, 12-14/06/2013, Nantes, France

Multon B., Aubry J., Haessig P., Ahmed H.B., Systèmes de stockage d'énergie électrique, Techniques de l'ingénieur, Réf. BE8100, 04/2013

Murzyn F., Furgerot L., Mouazé D., Tessier B., Pérez L., Experimental study of a tidal bore : free surface and velocity measurements, 1st Workshop on Environmental Fluid Mechanics, Geophysical Flows and Modeling, University of Queensland, 2013, Brisbane, Australie

Truong Hoang T.Q., Tran D.T., Comportement mécanique d'un composite à base de fibres tissées de chanvre et de résine époxy biosourcée, JNC18, 12-14/06/2013, Nantes, France

Truong Hoang T.Q., Tran D.T., Mechanical behavior of hemp-fibers woven fabric / bio-based epoxy composite (poster), JNC18, 12-14/06/2013, Nantes, France

2012

Articles avec comité de lecture

Azib T., Larouci C., Chaïbet A., Boukhnifer M., On-line energy management strategy of a hybrid fuel cell / battery / ultracapacitor vehicular power system, IET Electrical Systems in Transportation, 2012

Boudjedir H., Bouhali O., Rizoug N., Neural network control based on adaptive observer for quadrotor helicopter, International Journal of Information Technology, Control and Automation (IJITCA), Vol. 2 N°3, p. 39-54, 07/2012

Boukhnifer M., Chaïbet A., Azib T., Larouci C., Design of tele-control electrical vehicle system using fuzzy logic control, International Journal of Advanced Robotic Systems : Mechatronics, Vol. 9, 11/2012

Ejjabraoui K., Larouci C., Lefranc P., Marchand C., Pre-sizing methodology of dc-dc converters using optimization under multi-physic constraints; Applications to a buck converter, IEEE Transactions on Industrial Electronics, Vol. 59 N° 7, p. 2781-2790, 2012

Lagache J-M., Assaf S., Elimination of internal structural variables through explicit Taylor-Laurent model reduction, with applications to damped sandwich plates, Acta Acustica united with Acustica, Vol. 98, 03/2012

Larouci C., Ejjabraoui K., Lefranc P., Marchand C., Impact of control constraint on a multi-objective buck converter design, International Journal of Power Electronics and Drive Systems, Vol. 2 n° 3, 09/2012

Larouci C., Ejjabraoui K., Lefranc P., Marchand C., Placement optimization of power components in static power converters under spatial and thermal constraints, Journal of Power Electronics, Vol. 12 N°2, p. 368-376, 2012

Lascoup B., Aboura Z., Khellil K., Benzeggagh M.L., Prediction of out-of-plane behavior of stitched sandwich structure, Composites part B, Vol. 43 N° 8, p. 2915-2920, 12/2012

Mehel A., Sagot B., Tanière A., Oesterlé B., On the mutual effect of the turbulent dispersion model and thermophoresis on nanoparticle deposition, International Journal of Nonlinear Sciences and Numerical Simulation, Vol. 13 n°6, p. 417-425, 2012

Rizoug N., Bartholomeüs P., Le Moigne P., Study of the Ageing Process of a Supercapacitor Module Using Direct Method of Characterization, IEEE Transactions on Energy Conversion, Vol. 27, p. 220-228, 06/2012

Zhang Y., Abraham O., Grondin F., Loukili A., Tournat V., Le Duff A., Lascoup B., Durand O., Study of stress-induced velocity variation in concrete under direct tensile force and monitoring of the damage level by using thermally-compensated CODA wave interferometry, Ultrasonics, Vol. 52 N° 8, p. 1038-1045, 12/2012

Communications internationales

Assaf S., Vibration and analysis of viscoelastically damped composite sandwich plates, ICSV 19, 8-12/07/2012, Vilnius, Lituanie

Azib T., Larouci C., Boukhnifer M., Chaïbet A., Fuel-cell / ultracapacitor based hybrid emergency power system for more electric aircraft, More electric aircraft 2012 MEA'12, 20-21/11/2012, Bordeaux, France

Ben Tahar M., Hello G., Bedrici N., Acoustic emission during crack growth by a hybrid semi-analytical / BEM model, 30th European Conference on Acoustic Emission Testing and 7th International Conference on Acoustic Emission, 12-15/09/2012, Grenade, Espagne

Boukhnifer M., Chaïbet A., Azib T., Larouci C., Fuzzy logic design for tele-control electrical vehicle, IEEE Multiconference on Systems, Signals and Devices SSD'2012, 20-23/03/2012, Chemnitz, Allemagne

Boukhnifer M., Chaïbet A., Azib T., Larouci C., Tele-control electrical vehicle system using wave variables, IEEE Multiconference on Systems, Signals and Devices SSD'2012, 20-23/03/2012, Chemnitz, Allemagne

Boukhnifer M., Chaïbet A., Azib T., Larouci C., H-infinity robust control of 3-DOF helicopter, IEEE Multiconference on Systems, Signals and Devices SSD'2012, 20-23/03/2012, Chemnitz, Allemagne

Boukhnifer M., Raisemche A., Fault tolerant control for induction motor in electrical vehicle, IEEE Multiconference on Systems and Control MSC 2012, p. 136-141, 3-5/10/2012, Dubrovnik, Croatie

Chaaban K., Rizoug N., Barbedette B., Saudrais S., Model-based Development of an Embedded Steering-by-wire System, ISMA 2012, 10-12/04/2012, Sharjah, Emirats Arabes Unis

Chaïbet A., Boukhnifer M., Commande robuste d'un hélicoptère à trois degrés de liberté (03ddl), IEEE Conference Internationale Francophone d'Automatique CIFA 2012, 04-06/07/2012, Grenoble, France

Daghsen A., Chaaban K., Saudrais S., Software function allocation and configuration of an AUTOSAR-compliant system, SAE 2012 World Congress & Exhibition, 24-26/04/2012, Detroit, USA

Gelineau P., Lascoup B., Jendli Z., Le Gorju Jago K., Acoustic emission approach to quantify damage evolution, ECCM 15, 24-28/06/2012, Venise, Italie

Hammani A., Sadoun R., Rizoug N., Bartholomeüs P., Barbedette B., Le Moigne P., Influence Of The Management Strategies On The Sizing Of Hybrid Supply Composed With Battery And Supercapacitor, IEEE REVET 2012, 26-28/03/2012, Hammamet, Tunisie

Hammani A., Sadoun R., Rizoug N., Bartholomeüs P., Barbedette B., Le Moigne P., Influence Des Stratégies De Gestion d’énergie Sur Le Dimensionnement Des Sources Hybride - Batterie & Supercondensateur- Alimentant Un Véhicule Electrique, IEEE EPF’2012, 05-07/07/2012, Bordeaux, France

Lagache J-M., Assaf S., Low frequency m-k-M equivalence on local quasi-rigid interfaces, ICSV 19, 8-12/07/2012, Vilnius, Lituanie

Lagache J-M., Assaf S., Static correction of acoustic models with application to vibro-acoustic coupling, Acoustics 2012, 23-27/04/2012, Nantes, France

Lascoup B., Defect detection based on thermal periodic exicitation, ECCM 15, 24-28/06/2012, Venise, Italie

Mehel A., The influence of the dispersion model and electrochemical forces on nanoparticle deposition in a turbulent flow, Proceedings 7th International Symposium on Turbulence, Heat and Mass Transfer - THMT'12, 24-27/09/2012, Palerme, Italie

Mehel A., Effect of the electrochemical forces on nanoparticle deposition in a turbulent flow, Proceedings 10th International Conference on Industrial Ventilation - Ventilation'2009, 24-27/09/2012, Paris, France

Migaud J., Marimbordes T., Gutfrind C., Dufour L., Sagot B., Lefranc P., Fianni P., Optimization in air intake and EGR systems to Euro 6 standard and CO2 reduction, International Conference on Diesel Powertrain, 5-6/06/2012, Rouen, France

Remy G., Bethoux O., Azib T., Riera J., Sera M., Analyses of energy management strategies for minimizing the hydrogen use in PEMFC HEV, IEEE VPPC 2012, 9-12/10/2012, Séoul, Corée du Sud

Rizoug N., Feld G., Barbedette B., Sadoun R., Starter-alternator propel the vehicle through a hybrid : battery and supercapacitors, APEC 2012, 05-09/02/2012, Orlando, USA

Sadoun R., Rizoug N., Bartholomeüs P., Barbedette B., Le Moigne P., Sizing Of Hybrid Supply (Battery-Supercapacitor) For Electric Vehicle Taking Into Account The Weight Of The Additional Buck-Boost Chopper, IEEE REVET 2012, 26-28/03/2012, Hammamet, Tunisie

Sagot B., Comparison between available experimental data and theoretical models for the evaluation of deposition due to thermophoresis, Proceedings 10th International Conference on Industrial Ventilation, 17-19/09/2012, Paris, France

Sagot B., Buron F., Experimental study on the heat transfer in small cyclones, Proceedings 9th International Conference on Heat Transfer, Fluid Mechanics and Thermodynamics, 16-18/07/2012, La Valette, Malte

Sagot B., Buron F., Effect of flow regime and geometrical parameters on the heat transfer in blow-by gases cyclone separators, Proceedings 7th International Symposium on Turbulence, Heat and Mass Transfer, 24-27/09/2012, Palerme, Italie

Sagot B., Giardi J., Experimental study on small cyclones for combustion engine gas cleaning, European Aerosol Conference, 02-07/09/2012, Grenade, Espagne

Sehab R., Emulation of an electrohydraulic actuator associated to an aerodynamic load and validation usign electric machines, LMS European Aerospace Conference, 4-5/10/2012, Toulouse, France

Sehab R., Feld G., An online estimation of energy recovery in an electric vehicle using ARTEMIS mission profiles, IEEE Vehicle Power and Propulsion Conference VPPC 2012, 9-12/10/2012, Séoul, Corée du Sud

Soubra H., The use and benefits of functional size measurement in the context of Autosar, UKSMA 12, 8-11/12/2012, Londres, Royaume-Uni

Soubra H., Abran A., Ramdane-Cherif A., A defined functional size measurement procedure for real-time embedded software requirements expressed using the Simulink model, IWSM Mensura 2012, 17-19/10/2012, Assise, Italie

Soubra H., Chaaban K., Functional size measurement of electronic control units software designed following the Autosar standard, IWSM Mensura 2012, 17-19/10/2012, Assise, Italie

Zhang Y., Abraham O., Chapeleau X., Cottineau L.M., Tournat V., Le Duff A., Lascoup B., Durand O., Study of concrete's behavior under 4-point bending load using Coda Wave Interferometry (CWI) analysis, AIP Conference Proceedings, Vol. 1511, p. 398-404, 15-20/07/2012, Denver, USA

 

Autres

Lagache J-M., Assaf S., Cuvelier P., Acoustic design of resonators to reduce the noise level in a cabin, VCB 2012, 03-05/07/2012, Clamart, France

Ledoux C., Lefranc P., Larouci C., Optimisation du placement / routage de semiconducteurs de puissance : application à un hacheur abaisseur, EPF 2012, 05-07/07/2012, Bordeaux, France

Mangin P.E., Faux D., Cuvelier P., Tartary J.P., Modeling of the vibratory behavior of a wire rope spring by using the Dahl model with variable parameters, VCB 2012, 03-05/07/2012, Clamart, France

Rizoug N., Feld G., Barbedette B., Sadoun R., Using of hybrid supply electric or hybrid vehicles, Chapter book "Technology and Engineering Applications of Simulink", 05/2012

Sadoun R., Rizoug N., Bartholomeüs P., Le Moigne P., Hybrid power source (Li-ion battery-supercapacitor) supplying an electric vehicle, Research & Innovation for Transport Systems of the Future RITF 2012, 12-15/11/2012, Paris, France

Sehab R., Barbedette B., Fuzzy PID Supervision for an automotive Application : Design and Implementation, Chapter book "PID controller Design Approaches", Edited by M. Vagia, ISBN 9789535104056, 03/2012

Tchakaloff B., Saudrais S., Babau J.P., Modèles et transformations de modèles pour l'introduction de la consommation énergétique dans le standard Autosar, Conférence en Ingénierie du Logiciel CIEL, 19-21/06/2012, Rennes, France

2011

Articles avec comité de lecture

Assaf S., Finite element vibration analysis of damped composite sandwich beams, International Journal of Acoustics and Vibration, Vol. 16 n°4 n°4, 12/2011

Assaf S., Guerich M., Cuvelier P., Vibration and damping analysis of plates with partially covered damping layers, Acta Acustica, Vol. 97, 553-568, 07/2011

Bouhali O., Rizoug N., Talha A., Modelling and control of five-level three-phase flying capacitors inverter, International review on Modelling and Simulation, Vol. 4 N° 5, p. 2066-2073, 10/2011

Boukhnifer M., Chaïbet A., Larouci C., Passivity based control of teleoperated electric vehicle, Journal of Asian Electric Vehicles (JAEV), 2011

Chaïbet A., Boukhnifer M., Larouci C., Hybrid electric vehicle transmission chain simulator based on electromechanical actuators, Journal of Asian Electric Vehicles (JAEV), Vol. 9 N° 2, 12/2011

Chauvin M., Lascoup B., Contribution à l'allègement dans l'automobile : application à la liaison au sol, Revue de Métallurgie, Vol. 108 N° 7-8, p. 427-437, 2011

 

Communications internationales

Boukhnifer M., Chaïbet A., Larouci C., Experimental H-infinity Robust Control of Aerial Vehicle Flight, IEEE 19th Mediterranean Conference on Control and Automation (MED 2011), 20-23/06/2011, Corfou, Grèce

Daghsen A., Chaaban K., Saudrais S., Shawky M., Model transformation and scheduling analysis of an autosar system, ESA11, 18-21/07/2011, Las Vegas, USA

Hima S., Glaser S., Chaïbet A., Vanholme B., Controller design for trajectory tracking passenger vehicle, 14th International Conference on Intelligent Transportation Systems ITSC 2011, 05-07/10/2011, Washington DC, USA

Le Duff A., Eddine Hamdi S., Plantier G., Lascoup B., Time delay estimation for acoustic source location by means of short-time cross-correlation, IEEE Sensors 2011, p. 1885-1888, 28-31/10/2011, Limerick, Irlande

Ledoux C., Lefranc P., Larouci C., Thomas J.L., Pre-sizing optimization of an inverter and passive components, 14th European Conference on Power Electronics and Applications EPE'2011, 30/08-01/09/2011, Birmingham, Royaume-Uni

Mehel A., Sagot B., Tanière A., Oesterlé B., Effect of the turbulent dispersion models and thermophoresis on nanoparticle deposition, Proceedings of the 12th International Conference on Multiphase Flow in Industrial Plants, 21-23/09/2011, Ischia, Naples, Italie

Mehel A., Sagot B., Tanière A., Oesterlé B., Effect of the turbulent dispersion model on nanoparticle deposition in the presence of thermophoresis, INRS Occupational Health Research Conference 2011 : Risks associated to nanoparticles and nanomaterials, 05-07/04/2011, Nancy, France

Rahmi F., Aklouche H., Bedrici-Fraï N., Gatignol P., Potel C., Réflexion / transmission d'une onde plane sur une interface plane, First international conference on New Materials and Active Devices, 23-25/05/2011, Oum el Bouaghi, Algérie

Rizoug N., Feld G., Barbedette B., Sadoun R., Association of batteries and supercapacitors to supply a micro-hybrid vehicle, VPPC'11, 06-09/09/2011, Chicago, USA

Sadoun R., Rizoug N., Bartholomeüs P., Barbedette B., Le Moigne P., Optimal sizing of hybrid supply for electric vehicle using Li-ion batteries and supercapacitors, VPPC'11, 06-09/09/2011, Chicago, USA

Sadoun R., Rizoug N., Bartholomeüs P., Barbedette B., Le Moigne P., Influence of the drive cycles on the sizing of hybrid storage system battery-supercapacitor supplying an electric vehicle, IECON11, 07-10/11/2011, Melbourne, Australie

Saudrais S., Chaaban K., Automatic relocation of autosar components among several ecus, 14th International ACM SIGSOFT symposium on Component-based sofware engineering CBSE'11, 21-23/06/2011, Boulder, USA

Sehab R., Barbedette B., Chauvin M., Electric vehicle drivetrain: sizing and validation using general and particular mission profiles, ICM 2011, 13-15/04/2011, Istanbul, Turquie

Sehab R., Feld G., Drivetrain : emulation and simulation using electric machines, VPPC'11, 06-09/09/2011, Chicago, USA

Zhang Y., Abraham O., Larose E., Le Duff A., Lascoup B., Tournat V., Cottineau L.M., Monitoring the stress level of concrete structures with CODA wave interferometry: influence of temperature on long lasting monitoring experiment, NDTMS 2011, International Symposium on Nondestructive Testing of Materials and Structures, 15-18/05/2011, Istanbul, Turquie

 

Autres

Barbedette B., Rizoug N., Sadoun R., Sehab R., L'hybridation des systèmes de stockage d'énergies embarquées, Journée Scientifique et Technique, thème : la filière automobile face aux normes environnementales : contraintes ou opportunités, 2011, Laval, France

Chaaban K., A distributed real-time architecture for advanced vehicles, LAP LAMBERT academic publishing, 04/2011

Cuvelier P., Chevallier Q., Comparaison expérimentale de mesures holographiques en champ proche - formation de voies avec des mesures obtenues au vibromètre laser, Faites de la mesure, 21-23/06/2011, Société Brüel & Kjaer, Mennecy, France

Cuvelier P., Chevallier Q., Repliement en formation de voies 1D et 3D, Faites de la Mesure, 21-23/06/2011, Société Brüel & Kjaer, Mennecy, France

Daghsen A., Chaaban K., Shawky M., Méthodes d'allocation / optimisation des ressources : application de l'approche de design space exploration sur un système autosar, 4ème Colloque Automatique et Réseaux de Communication ARC, 01/04/2011, Paris, France

Hassar M., Lascoup B., Aboura Z., Benzeggagh M.L., Effet des nanoparticules de noir de carbone sur l'efficacité de blindage électromagnétique de composites, JNC 17 17èmes journées Nationales sur les Composites, 15-17/06/2011, Poitiers, France

Lascoup B., Chauvin M., Contribution à la conductivité thermique d'un matériau composite, JNC 17 17èmes journées Nationales sur les Composites, 15-17/06/2011, Poitiers, France

Lascoup B., Perez L., Autrique L., Crinière A., Détection de défauts à l'aide d'une sollicitation thermique : étude de faisabilité, JNC 17 17èmes journées Nationales sur les Composites, 15-17/06/2011, Poitiers, France

Sadoun R., Rizoug N., Bartholomeüs P., Le Moigne P., Influence des cycles de conduite sur le dimensionnement du système de stockage hybride batterie - supercondensateur alimentant un véhicule électrique, EF'11, 12/2011, Belfort, France

Sagot B., Mehel A., Antonini G., Evaluation des performances de dépôt d'un réacteur à gradient de température contrôlé, appliqué à la capture des fines particules, Congrès française de Thermique, 24-27/05/2011, Perpignan, France

Saudrais S., Qualité de service temporelle pour composants logiciels, Editions Universitaires Européennes, 01-2011

Truong Hoang T.Q., Touchard F., Comportement en statique et à l'impact de composites à base de fibres non-tissées de lin et de polypropylène, JNC17, 15-17/06/2011, Poitiers, France

Zhang Y., Abraham O., Durand O., Grondin F., Saliba J., Loukili A., Tournat V., Le Duff A., Lascoup B., Monitoring creep with CODA wave interferometry: experimental illustration on a three points bending concrete beam, Journées Cofrend, 24-27/05/2011, Dunkerque, France

2010

Articles avec comité de lecture

Assaf S., Guerich M., Cuvelier P., Vibration and acoustic response of damped sandwich plates immersed in a light or heavy fluid, Computers and Structures, Vol. 88 N°13-14, Juillet 2010

Boukhnifer M., Chaïbet A., Larouci C., H-infinity Robust Speed Control Architecture for Ultrasonic Motor, Mediterranean Journal of Measurement and Control, 2010

Gatignol P., Potel C., Bedrici N., Improvement of the computation of Fourier integrals using the complex plane: application to acoustic fields, Applied physics letters, N° 96, 044103, 2010

Larouci C., Boukhnifer M., Chaïbet A., Design of Power Converters by Optimization Under Multi-physic Constraints; Application to a Two-Time Scales AC/DC-DC Converter, IEEE Transactions on Industrial Electronics, Vol.57 N°11, p. 3746-3753, 11/2010

Lascoup B., Aboura Z., Khellil K., Benzeggagh M.L., Homogenization of the core layer in stitched sandwich structures, Composites Science and Technology, Volume 70, Issue 2, p. 350-355, Février 2010

Lascoup B., Aboura Z., Khellil K., Benzeggagh M.L., Impact response of three-dimensional stitched sandwich composite, Composite Structures, Volume 92, Issue 2, p. 347-353, Janvier 2010

Rizoug N., Bartholomeüs P., Le Moigne P., Modeling and Characterizing Supercapacitors Using an On-Line Method, IEEE Transactions on Industrial Electronics, N°99, 2010

Sagot B., Antonini G., Buron F., Enhancement of jet-to-wall heat transfer using axisymmetric grooved impinging plates, International Journal of Thermal Sciences, Vol. 49 issue 6, 06/2010

Truong Hoang T.Q., Lagattu F., Brillaud J., Natural fibre reinforced recycled polypropylene: Microstructural and mechanical properties, Journal of Reinforced Plastics and Composites, Vol. 29, No. 2, p. 209-217, 2010

 

Communications internationales

Assaf S., Guerich M., Damping analysis of beams with partial coverage, MCA 2010, 28 – 30 Octobre 2010, Sale, Maroc

Bouhali O., Rizoug N., Saudemont C., Talha A., A New Modelling And Control Algorithm Of A Three-Phase Five-Level Neutral Point Clamped (NPC) Converter, IEEE ICECS 2010, 12-15/12/2010, Athènes, Grèce

Boukhnifer M., Haj Salem H., Evaluation Opérationnelle de la Régulation d’Accès sur les Autoroutes de l’IDF Basée sur la Stratégie ALINEA, IEEE Conférence Internationale Francophone d'Automatique (CIFA’10), 2-4/06/2010, Nancy, France

Chauvin M., Lascoup B., of the twist beam rear axle in using composites materials, ECCM 14, 7-10/06/2010, Budapest, Hongrie

Ejjabraoui K., Larouci C., Lefranc P., Marchand C., Pre-sizing approach by optimization of a Boost converters and design of controller parameters to ensuring stability, PCIM 2010, 4-6/05/2010, Nuremberg, Allemagne

Ejjabraoui K., Larouci C., Lefranc P., Marchand C., Pre-sizing of dc-dc converters by optimization under constraints; Influence of the control constraint on the optimization results, IEEE-ICIT 2010, 14-17/03/2010, Vina del Mar, Valparaiso, Chili

Haj Salem H., Boukhnifer M., Mabrouk H., Mammar S., Le contrôle d’accès généralisé sur les autoroutes de l’ile de France : études en simulation et sur site réel, 8th IFAC International Conference of Modeling and Simulation - MOSIM’10, 10-12/05/2010, Hammamet, Tunisie

Hassar M., Lascoup B., Strain rate influence on the failure stress of composite structure (poster), ECCM 14, 7-10/06/2010, Budapest, Hongrie

Hassar M., Lascoup B., Aboura Z., Benzeggagh M.L., Effect of the conducting particles on the process and mechanical behaviour of composite material, ECCM 14, 7-10/06/2010, Budapest, Hongrie

Lagache J-M., Assaf S., An explicit algebraic reduction technique, involving physical, generalized or modal coordinates, ISMA2010 Noise and Vibration Engineering conference, 20 - 22 September 2010, Louvain, Belgique

Lagache J-M., Cuvelier P., Assaf S., An experimental validation of the method of orthocomplement, MCA 2010, 28 – 30 Octobre 2010, Sale, Maroc

Ledoux C., Lefranc P., Larouci C., Thomas J.L., State of the art of mono-converter multi-loads applications and associated power electronic devices, IEEE ISIE'10, 07-10/07/2010, Bari, Italie

Ledoux C., Lefranc P., Larouci C., Thomas J.L., Cathelin J., Diallo D., Modeling and fault modes investigation of a power sharing AC drive, IEEE IECON'10, 07-10/11/2010, Glendale, USA

Murzyn F., Assessment of different experimental techniques to investigate the hydraulic jump : do they lead to the same results ?, Invited Keynote lecture, Hydraulic Structures : Useful water harvesting systems or relics ? Proceedings of the 3rd International Junior Researcher and Engineering Workshop on Hydraulic Structures IJREWHS'10, 02-03/05/2010, Edinbourg, Royaume-Uni

Rahmi F., Bedrici-Fraï N., Gatignol P., Potel C., Si-Chaib M.O., Génération d'ondes modales dans une structure multicouche périodique, par un faisceau ultrasonore borne sous incidence, IC-WNDT-MI’10, Conférence Internationale sur le Soudage, le CND et l’Industrie des Métaux, 27-28/11/2010, Oran, Algérie

Rizoug N., Feld G., Barbedette B., Hybrid Supply Using Supercapacitors For Start & Stop Vehicles, IEEE VDE 2010, 8-9/11/2010, Leipzig, Allemagne

Rizoug N., Feld G., Barbedette B., Hybrid supply for automotive application using supercapacitors, IEEE VPPC 2010, 1-3 septembre 2010, Lille, France

Zhang Y., Abraham O., Larose E., Planes T., Le Duff A., Lascoup B., El Guerjouma R., Cottineau L.M., Durand O., Following modifications of the stress level of concrete structures with CODA wave interferometry : estimation of the investigated zone, QNDE Quantitative nondestructive Evaluation, 18-23/07/2010, San Diego, USA

 

Autres

Boukhnifer M., Chaïbet A., Larouci C., Commande passive pour la téléopération d'un véhicule à distance, Revue e-STA électronique Sciences et Technologies de l'Automatique, Vol. 7 N°2, 2010

Boukhnifer M., Ferreira A., Aubry D., Robust Control for Ultrasonic Motor Operating within Harsh Environments, Chapter book “Mechatronic Systems Simulation Modeling and Control”, Edited by Annalisa Milella Donato Di Paola and Grazia Cicirelli, ISBN 978-953-307-041-4, Mars 2010

Boukhnifer M., Larouci C., Chaïbet A., Robust Shaping Indirect Field Oriented Control for Induction Motor, Chapter book “Mechatronic Systems Simulation Modeling and Control” ”, Edited by Annalisa Milella Di Paola and Grazia Cicirelli, ISBN 978-953-307-041-4, Mars 2010

Chaïbet A., Larouci C., Boukhnifer M., Vehicle Dynamic Model Coupled to Vehicle Transmission Simulator, Chapter book "Dynamic Modelling", Edited by Alisson V. Brito, ISBN 978-953-7619-68-8, Janvier 2010

Chauvin M., Lascoup B., Contribution à l’allègement dans l’automobile : “Application à la liaison au sol”, Matériaux 2010, 18-22 octobre 2010, Nantes, France

Daghsen A., Chaaban K., Saudrais S., Leserf P., Applying Holistic Distributed Scheduling to AUTOSAR Methodology, ERTS 2010, 19-21 mai 2010, Toulouse, France

Ejjabraoui K., Larouci C., Lefranc P., Marchand C., Modeling and design of a mechatronic actuator chain ; Application to a Motorized tailgate, Chapter book “Dynamic Modelling", Edited by Alisson V. Brito, ISBN 978-953-7619-68-8, Janvier 2010

Ejjabraoui K., Larouci C., Lefranc P., Marchand C., Approche multi-niveaux de pré-dimensionnement de convertisseurs statiques par optimisation sous contraintes multi-physiques, EPF 2010, 30 juin – 2 juillet 2010, Saint Nazaire, France

Gatignol P., Potel C., Bedrici N., Calcul numérique d'intégrales de Fourier en espaces complexes : applications à la simulation de techniques ultrasonores en contrôle non destructif des matériaux, Colloque Modélisation en mécanique des fluides, 17/11/2010, Lille, France

Lagache J-M., Assaf S., Algebraic reduction of finite-element acoustic models, VCB 2010, 15-17/06/2010, Lyon, France

Lascoup B., Aboura Z., Khellil K., Benzeggagh M.L., Influence de l’éclatement des mèches de couture sur le comportement mécaniques de structures sandwiches cousus, JST, Journées Scientifiques et Techniques AMAC, 26-27 mai 2010, Orléans, France

Leserf P., Réseaux embarqués pour l’automobile, application aux systèmes de commande électrique, Revue 3EI, Mars 2010

Mangin P.E., Tartary J.P., Cuvelier P., Caractérisation d'une suspension composée d'amortisseurs à câbles, VCB 2010, 15/17/06/2010, Lyon, France

Sagot B., Buron F., Antonini G., Transfert thermique dans les séparateurs cyclones appliqués à la dépollution automobile, Congrès français de Thermique, 25-28/05/2010, Le Touquet, France

Truong Hoang T.Q., Touchard F., Les non-tissé à base de fibres de lin et de polypropylène : caractérisation mécanique et microstructurale pour application automobile, Colloque "Le chanvre dans tous ses états : de la plante au composite", 18-19/03/2010, Poitiers, France

2009

Articles avec comité de lecture

Murzyn F., Chanson H., Experimental investigation of bubbly flow and turbulence in hydraulic jumps, Environmental Fluid Mechanics, Vol. 9 n° 2, p. 143-159, 2009

Murzyn F., Chanson H., Free-surface fluctuations in hydraulic jumps : experimental observations, Experimental Thermal and Fluid Science, Vol. 33 n° 7, p. 1055-1064, 2009

Murzyn F., Chanson H., Two-phase flow measurements in turbulent hydraulic jumps, Chemical Engineering Research and Design, Trans. IChemE Part A, Vol. 87 n° 6, p. 789-797, 2009

Sagot B., Antonini G., Buron F., Annular flow configuration with high deposition efficiency for the experimental determination of thermophoretic diffusion coefficients,, Journal of Aerosol Sciences, Vol. 40 Issue 12, p. 1030-1049, 12/2009

 

Communications internationales

Assaf S., Free vibration analysis of composite sandwich beams with viscoelastic core, ISCV 16, 5-9 juillet 2009, Cracovie, Pologne

Assaf S., Guerich M., Cuvelier P., Vibration and damping analysis of partially damped plates, Euronoise 2009, 26-28/10/2009, Edimbourg, Royaume-Uni

Assaf S., Lagache J-M., Elimination of internal structural variables through explicit Mac-Neal modal reduction, Euronoise 2009, 26-28/10/2009, Edimbourg, Royaume-Uni

Boukhnifer M., Chaïbet A., Larouci C., A Robust Speed Control Architecture for Ultrasonic Motor, IEEE IECON’09, 3-5 November 2009, Porto, Portugal

Boukhnifer M., Larouci C., Chaïbet A., Fault Tolerant Control of Piezoelectric Traveling Wave Ultrasonic Motor, IEEE MSC- Conference on Control Applications (CCA'09), July 8-10, 2009, Saint Petersbourg, Russie

Chaaban K., Leserf P, Saudrais S., Steer-by-wire development using AUTOSAR methodology, IEEE ETFA 09, 22-26/09/2009, Palma de Majorque, Espagne

Chaaban K., Shawky M., Crubillé P., A distributed embedded architecture for the evaluation of ADAS systems, Proceedings of the 12th IFAC Symposium on Control in Transportation Systems (CTS’09), 2-4/09/2009, Californie, USA

Chaaban K., Simulation of a Steer-By-Wire System Using FlexRay-based ECU Network, International conference on advances in computational tools for engineering applications, ACTEA 2009, 15-17/07/2009, Beyrouth, Liban

Chaïbet A., Boukhnifer M., Larouci C., Estimation for Integrated Longitudinal and Lateral Car Following Control, IEEE MSC- Conference on Control Applications (CCA'09), July 8-10, 2009, Saint Petersbourg, Russie

Chauvin M., Lascoup B., Applications des composites pour des pièces structurelles dans l'automobile, 9ème Congrès de Mécanique, 21-24/04/2009, Marrakech, Maroc

Cuvelier P., Giardi J., Pham A-T., Reduction of the first torsional mode of a structure by a gyroscopic damper, 15th international Conference of the Vehicle Dynamics, 23-24/09/2009, Lyon, France

Ejjabraoui K., Larouci C., Lefranc P., Marchand C., A new pre-sizing approach of dc-dc converters, application to a Boost converter for the automotive domain, IEEE IECON’09, 3-5 November 2009, Porto, Portugal

Ejjabraoui K., Larouci C., Lefranc P., Marchand C., A pre-sizing approach by optimization of DC-DC converters, application to Design a Buck converter for the automotive domain, International Power Electronics and Motion Control IEEE IPEMC’09, 17-20 May 2009, Wuhan, Chine

Ejjabraoui K., Larouci C., Lefranc P., Marchand C., Pre-sizing of dc-dc buck converter for the automotive domain, Power Conversion and Intelligent Motion Conference PCIM'09, 12-14 May 2009, Nuremberg, Allemagne

Lagache J-M., Assaf S., Explicit Mac Neal model reduction using accelerated modal formulae, ICSV 16, 5-9 juillet 2009, Cracovie, Pologne

Lagache J-M., Assaf S., Sauvage O., Direct truncation in modal expansions of structural or acoustic responses, MSC Software VPD Conference, 12-13 mai 2009, Münich, Allemagne

Larouci C., Chaïbet A., Boukhnifer M., A Vehicle Transmission Simulator Applied to the Automated Driving, IEEE 69th Vehicular Technology Conference: VTC2009-Spring, 26–29 April 2009, Barcelone, Espagne

Larouci C., Design of power converters by optimization under constraints; Application to a two time scales AC/DC-DC converter, International Conference on Industrial Technology, IEEE ICIT’09, 10-13 February 2009, Victoria, Australie

Murzyn F., Chanson H., Non-intrusive measurement technique for dynamic free-surface characteristics in hydraulic jumps, Proceedings of the 33rd IAHR Biennal Congress IAHR-ASCE-EWRI, 09-14/08/2009, Vancouver, Canada

Remy G., Ejjabraoui K., Larouci C., Mhenni F., Sehab S., Lefranc P., Barbedette B., Raka S.A., Combastel C., Cannou S., Cardon F., Cuvelier P., Marchand C., Lizuka B., Bastard P., Barbier D., Modeling Guidelines and Tools Comparison for Mechatronics System Design in Automotive Applications. Application to a Motorized Hatchback, Proceedings of EMM2009, Mechatronics for vehicles and production, 24-25/06/2009, Paris, France

Saudrais S., Staikopoulos A., Clarke S., Using Specification Models for RunTime Adaptations, Proceedings of the Models@Runtime workshop at Models 2009, 4-9/10/2009, Denver, USA

Sehab R., An Aerodynamic Load for an Electrohydraulic Actuator: Advanced Modelling and Implementation Using Electric Actuators, 13th World Multiconference on Systemics, Cybernetics and Informatics, 10-13/07/2009, Orlando, USA

Sehab R., Rizoug N., Feld G., Barbedette B., Transmission Chain for Series-Parallel Hybrid Vehicle: Simulation and Sizing Using Electric Actuators, EMM’2009, p. 1-10, 24-25/06/2009, Paris, France

 

Autres

 

Chauvin M., Lascoup B., Influence of composite parts on the dynamics behavior of an automotive steering column, JNC16 16èmes Journées Nationales sur les Composites, 10-12/06/2009, Toulouse, France

Cuvelier P., Giardi J., Pham A-T., Atténuation du premier mode de torsion d’une structure par un batteur gyroscopique, Mécanique & Industrie, Avril 2009

Gillet S., Chaïbet A., Dimitrijevic Z., Impact Harshness and steering input response on a twist beam axle : Improvement by using magneto rheological bushing, SIA- Dynamique du véhicule, 15ième Congrès international, 24/09/2009, Lyon, France

Lascoup B., Chauvin M., Influence de l'introduction d'éléments en composite sur le comportement dynamique d'une direction automobile, JNC16 16èmes Journées Nationales sur les Composites, 10-12/06/2009, Toulouse, France

Murzyn F., Chanson H., Two-phase gas-liquid flow properties in the hydraulic jumps : review and perspectives, Multiphase Flow Research, Nova Science Publishers, Chapter 9, p. 497-542, 2009

Rizoug N., Systèmes électriques pour véhicules du futur, Journées de la section électrotechnique du club EEA, 11-12/03/2009, Lille, France

Rizoug N., Feld G., Barbedette B., Source hybride pour le démarrage d’un véhicule, EF’2009, 24-25/09/2009, Compiègne, France

Rizoug N., Feld G., Barbedette B., Hybrid Supply For The vehicle Starting-Up, Automotive Power Electronics APE’2009, 25-26/03/2009, Paris, France

2008

Articles avec comité de lecture

  

Assaf S., Guerich M., Numerical Prediction of Noise Transmission Loss through Viscoelastically Damped Sandwich Plates, Journal of Sandwich Structures and Materials, Vol. 10, p. 359-384, Septembre 2008

Assaf S., Guerich M., Influence of temperature on sound transmission through viscoelastic sandwich plates, Journal of Acoustical Society of America, Vol. 123 N° 5, Mai 2008

Lagache J-M., Assaf S. , Schulte C., Finite element synthesis of structural or acoustic receptances in view of practical design applications, Journal of Sound and Vibration, Vol. 310 n° 1-2, 02/2008

Murzyn F., Chanson H., Experimental assessment of scale effects affecting two-phase flow properties in hydraulic jumps, Experiments in Fluids, Vol. 45 n° 3, p. 513-521, 2008

Sagot B., Antonini G., Christgen A., Buron F., Jet impingement heat transfer on a flat plate at a constant wall temperature,, International Journal of Thermal Sciences, Vol. 47 Issue 12, p. 1610-1619, 12/2008

 

Communications internationales

 

Chaïbet A., Larouci C., An electric simulator of a vehicle transmission chain coupled to a vehicle dynamic model, IEEE IECON'08, 10-13 novembre 2008, Orlando, USA

Gresil M., Efficacité de blindage par l'insertion d'un écran métallisé dans les matériaux composites verre et carbone, CEM08, 14ème colloque international sur la compatibilité électromagnétique, 20-23/05/2008, Paris, France

Gresil M. , Parneix P. , Boulay J., Cheype C., Walrick J-C., Lascoup B., Mechanical effect and shielding effectiveness of the insertion of metallic screen in glass and carbon composite, ECCM13 13ème Conférence Européenne sur les Matériaux Composites, 2-5/06/2008, Biarritz, France

Guerich M., Assaf S., Parametric study of noise transmission loss of damped sandwich structures, 12th AIAA / ISMO Multidisciplinary Analysis and Optimization Conference, 10-12 septembre 2008, Victoria, Canada

Guerich M., Assaf S., Optimization of noise transmission loss of damped sandwich structures, ISMA 2008, 15-17 septembre 2008, Louvain, Belgique

Lagache J-M., Assaf S., Sauvage O., Modal synthesis using accelerated modal summations, ISMA 2008, 15-17 septembre 2008, Louvain, Belgique

Larouci C., Pre-sizing of power converters using optimization under constraints, IEEE International Conference on Industrial Technology (ICIT 2008), 21-24 avril 2008, Chengdu, Chine

Larouci C., Chaïbet A., Coupling of a vehicle transmission chain simulator using a sliding mode control with a vehicle dynamic model, IEEE Vehicle Power and Propulsion Conference (VPPC'08), 3-5 septembre 2008, Harbin, Chine

Lascoup B., N'Diaye P., Impact behavior of automotive shock absorbing beam : experimental and numerical representation, ECCM13, 13ème Conférence Européenne sur les Matériaux Composites, 2-5/06/2008, Biarritz, France

Sagot B., Antonini G., Buron F., Enhancement of the thermophoretic aerosol particles deposition efficiency in a turbulent annular flow configuration, 10th World Filtration Congress, April 14 - 18, 2008, Leipzig, Allemagne

Chanson H., Murzyn F., Froude similitude and scale effects affecting air entrainment in hydraulic jumps, Proceedings of the World Environmental and Water Resources Congress, 13-16/05/2008, Ahupua'a, Hawaï, USA

 

Autres

 

Assaf S., Lagache J-M., Modal finite element synthesis of acoustic boundary receptances, Mécanique & Industrie, N°9, p. 579-588, 2008

Rizoug N., Bartholomeüs P., Le Moigne P., Caractérisation d'un module supercondensateur pour des contraintes électriques de type traction, Revue Internationale de Génie Electrique, 09/2008

Sagot B., Antonini G., Buron F., Intensification du rendement de captation d’un impacteur par effet thermophorétique, 23ième Congrès Français sur les Aérosols, 16-17 /01/2008, Paris, France

 

2007

Articles avec comité de lecture

 

Bertoncini P., Gresil M., Lardoux J., Riou I., Chauvet O., Morphology of DNA / single walled nanotubes complexes, Digest Journal of Nanomaterials and Biostructures, Vol. 2 n°4, p. 293-297, Décembre 2007

Grunn E., Pham A-T., Modélisation OD appliquée à la dynamique automobile, Journal Européen des Systèmes Automatisés, Mai 2007

Murzyn F., Mouazé D., Chaplin J.R., Air water interface dynamic and free surface features in hydraulic jumps, Journal of Hydraulic Research, Vol. 45 n° 5, p. 679-685, 2007

 

Communications internationales

 

Bertoncini P., Gresil M., Bonnet P., Chauvet O., AFM imaging and force spectroscopy: tools for studying plant and surface and characterizing carbon nanotubes / bio-molecules hybrids, AFM BioMed Conference, 19-21 avril 2007, Barcelone, Espagne

Chauvin M., Amblard M., A Weight reduction study of chassis parts on the elasto-kinematic behavior and using Advanced High Strengh steel, Vehicle Dynamics Expo, 9th May 2007, Stuttgart, Allemagne

Larouci C., Volume optimisation of power converters under electromagnetic compatibility, thermal, efficiency and control constraints, 2nd International conference in Automotive Power Electronics APE'07 of SIA, 26-27/09/2007, Paris, France

Larouci C., Dehondt E., Harakat A., Feld G., Modelling and control of the vehicle transmission chain using electric actuators ; Integration of a clutch, IEEE ISIE'07, June 4-7, 2007, Vigo, Espagne

Lascoup B., Aboura Z., Benzeggagh M.L., Stitching effect on static and dynamic behaviour of sandwich structures, ICSS7 7ème International Congress on Sandwich Structures, 29-31/08/2007, Aalborg, Danemark

Lascoup B., Aboura Z., Khellil K., Benzeggagh M.L., Cycling behaviour of stitched composite sandwich structure, Fatigue Design 2007, 2nd International Conference on the Respective Input of the Numerical and Experimental Approach in Fatigue, 21-22/11/2007, Senlis, France

Sehab R., Fuzzy PID supervision for a non linear system: design and implementation, North American Fuzzy Information Processing Society Conference, 24-27/06/2007, San Diego, USA

 

Autres

 

Bartholomeüs P., Rizoug N., Pierre X., et al., Influence de la température sur l'évolution du déséquilibre de tension pour un module de supercondensateurs 56V / 96F, Revue 3EI, N°51, 30-36, Décembre 2007

Chauvin M., Amblard M., Allègement des liaisons au sol par introduction d’Acier THR : méthodologie et résultat, SIA- Dynamique du véhicule, 14ième Congrès international, 21/06/2007, Lyon, France

Larouci C., Feld G., Simulateur à base d'actionneurs électriques pour la chaine de transmission automobile, Revue 3EI, N°48, Mars 2007

Lascoup B., Comportement de l'interface âme / peau d'un sandwich cousu face à une sollicitation de délaminage en mode I, JNC15 15èmes Journées Nationales sur les Composites, 06-08/06/2007, Marseille, France

Murzyn F., Les écoulements multiphasiques appliqués aux problèmes environnementaux. Le cas du ressaut hydraulique, Séminaire ESTACA à l'attention des étudiants, 2007, Laval, France

Murzyn F., Research interests. Experimental works on hydraulic jumps, Intern Seminar, University of Queensland, 2007, Brisbane, Australie

Murzyn F., Chanson H., Free surface, bubbly flow and turbulence measurements in hydraulic jumps, Hydraulic Model report CH63/07, University of Queensland, Division of Civil Engineering, 2007, Brisbane, Australie

Rizoug N., Bartholomeüs P., Le Moigne P., Modélisation et caractérisation de supercondensateurs en cyclage, Revue Internationale de Génie Electrique, Vol. 10 N°5, p. 641, 10/2007

Sagot B., Antonini G., Buron F., Séparation gaz-particules par piège thermophorétique tri-therme, 1ères Journées Filtration des Aérosols, 7-8/06/2007, Nancy, France

Sagot B., Antonini G., Buron F., Transfert thermique par jet impactant sur plaque plane corruguée, Congrès Français de Thermique, 29 mai-1er juin 2007, Île des Embiez, France

Walrick J-C., Assaf S., Longrais P., Optimisation numérique d'une suspension de véhicule en sollicitation dynamique, Mécanique & Industrie, Vol. 7, p. 445-452, 03/2007

 

2006

Articles avec comité de lecture

 

Coutellier D., Walrick J-C., Geoffroy P., Presentation of a methodology for delamination detection within laminated structures, Composites Science and Technology, Vol. 66 N° 6, 837-845, Mai 2006

Lascoup B., Aboura Z., Khellil K., Benzeggagh M.L., On the mechanical effect of stitch addition in sandwich panel, Composites Science and Technology, Volume 66, Issue 10, p. 1385-1398, Août 2006

Murzyn F., Mouazé D., Chaplin J.R., Flow visualization and free surface length scales measurements in a horizontal jet beneath a free surface, Experimental Thermal and Fluid Science, Vol. 30 n° 7, p. 703-710, 2006

 

Communications internationales

 

Bonnet P., Chauvet O., Bertoncini P G., et al., Elaboration and characterization of amylose / SWNT complexes, 2006 International Conf. on Science and Technology of Synthetic Metals, 02-07/07/2006, Dublin, Irlande

Gillet S., Oukka A., Suspension Coil Spring and Rubber Insulators: towards a methodology of global design, Technical paper-suspension session- Vehicle Dynamics, Vehicle Dynamics Expo, 9-11 mai 2006, Stuttgart, Allemagne

Larouci C., Optimization under constraints of a forward converter, PCIM'06, 20-22/05/2006, Nuremberg, Allemagne

Larouci C., Feld G., Didier J-P., A simulator of the vehicle transmission chain using electric machines, IEEE ISIE'06, July 9-13, 2006, Montréal, Canada

Larouci C., Feld G., Didier J-P., Modelling and control of the vehicle transmission chain using electric actuators, 32nd Annual Conference of the IEEE Industrial Electronics Society IECON'06, 07-10/11/2006, Paris, France

Lascoup B., Effets des paramètres géométriques de couture sur le comportement de structures sandwich cousues sous l'impact de faible énergie, 1er Congrès Méditerranéen sur les Matériaux Composites, 9-11/12/2006, Bechar, Algérie

Lascoup B., Modelling the in-plane shear behaviour of stitched sandwich structure, ECCM12, 12eme conférence européenne sur les matériaux composites, 29 août - 1 septembre 2006, Biarritz, France

Tamisier V., Optimal control of the gyroscopic effects, International Symposium on Industrial Electronics IEEE-ISIE 2006, MagLev Session, 09-13/07/2006, Montréal, Canada

 

Autres

 

Lascoup B., Aboura Z., Khellil K., Benzeggagh M.L., Structures sandwichs composites 3D de nouvelle génération, Revue des Composites et des Matériaux Avancés, Vol. 16 N°3, p. 279-304, 2006

Sagot B., Antonini G., Buron F., Couplage de transferts pour l’intensification des dépôts particulaires sur une paroi plane refroidie, impactée par un jet de gaz chargé, Congrès Français de Thermique, 16-19/05/2006, Île de Ré, France

 

2005

Articles avec comité de lecture

Mouazé D., Murzyn F., Chaplin J.R., Free surface length scale estimation in hydraulic jumps, Journal of Fluids Engineering, Vol. 127 n° 6, p. 1191-1193, 2005

Murzyn F., Bélorgey M., Experimental investigation of the grid-generated turbulence features in a free surface flow, Experimental Thermal and Fluid Science, Vol. 29 n° 8, p. 925-935, 2005

Murzyn F., Bélorgey M., Wave influence on turbulence length scales in free surface channel flows, Experimental Thermal and Fluid Science, Vol. 29 n° 2, p. 179-187, 2005

Murzyn F., Mouazé D., Chaplin J.R., Optical fibre probe measurements of bubbly flow in hydraulic jumps, International Journal of Multiphase Flow, Vol. 31 n° 1, p. 141-154, 2005

 

Communications internationales

 Larouci C., Optimization of a 42V/14V dc-dc converter for vehicular electrical network, IEEE VTC'05-Spring, 30 mai - 01 juin 2005, Stockholm, Suède

Tamisier V., Rotating machine on active magnetic bearings: a didactic tool for mechatronics, REM2005, 28-29/06/2005, Annecy, France

 

Autres

 Esquiva-Dano I., Giardi J., Sagot B., Buron F., Antonini G., Amélioration de l’efficacité des pièges thermophorétiques par utilisation de dispositifs tri-thermes, 17ème Congrès Français de Mécanique, Septembre 2005, Troyes, France

Larouci C., L'énergie éolienne : état de l'art, Revue E3I, N°40, Mars 2005

Larouci C., Didier J-P., Modélisation et commande d'une éolienne, Revue E3I, N°40, Mars 2005

Larouci C., Didier J-P., Selvez M., Prado S., L'électronique de puissance et le véhicule de demain : optimisation d'un convertisseur 42 V-14 V sous des contraintes d'encombrement, de rendement, de compatibilité électromagnétique et thermiques, Revue de l'Electricité et de l'Electronique, Mars 2005

Lestriez P., Saanouni K., Cherouat A., Simulation numérique de la coupe orthogonale par couplage thermique - comportement - endommagement, Congrès Français de Mécanique, 29 août - 2 septembre 2005, Troyes, France

 

2004

Communications internationales

Tamisier V., A multi-objective control algorithm: application to an amb machine, 9th International Symposium on Magnetic Bearings, 03-06/08/2004, Lexington, USA

Tamisier V. , Font S., Optimal vibration control of a milling electrospindle, 9th International Symposium on Magnetic Bearings, 03-06/08/2004, Lexington, USA

Larouci C., Didier J-P., Prost A., et al., Optimal design of a boost converter using analytical models, PCIM'04, 25-27 mai 2004, Nuremberg, Allemagne

Larouci C., Didier J-P., de Crevecoeur A., Vauchel J., An optimization under constraints approach using a specific optimizaton tool : application to design a buck converter, IEEE ISIE'04, 04-07/05/2004, Ajaccio, France

2003

Communications internationales

Clavier A., Alirand M., Vernat F., Sagot B., Local Approach to improve the global approach of Hydraulic Forces in ball poppet valves, 4th Int. Symposium on Fluid Power, April 8-10 2003, Wuhan, Chine

Larouci C., Didier J-P., Aldebert A., Bouquet O., Optimal design of a synchronous dc-dc converter using analytical models and a dedicated optimization tool, IEEE IECON'03, 02-06 novembre 2003, Roanoke, USA

Larouci C., Didier J-P., Analytical models to optimize a synchronous DC-DC, IEEE CESA'03, 09-12/07/2003, Lille, France

Larouci C., Didier J-P., Selvez M., Volume Optimisation of static converters under electromagnetic compatibility, loss and temperature constraints, 24th international PCIM Conférence - PCIM'03, 20-23/05/2003, Nuremberg, Allemagne

Walrick J-C., Assaf S., Physics-based performances validations of a suspension system with Pam Medysa 2G, Colloque International EUROPAM 2003, 16-17/10/2003, Mayence, Allemagne

Autres

Buron F., Sagot B., Antonini G., Manes L., Détermination des efficacités de captation particulaire en mélange diphasique air/huile dans un dispositif de séparation à filtre rotatif, VIIème Rencontre Utilisateurs FLUENT, Octobre 2003, Paris, France

Didier J-P., Halconruy T., Outil de simulation pour la spécification des systèmes de dynamique véhicule, Congrès SIA, Juin 2003, Lyon, France

Larouci C., Didier J-P., Selvez M., L'électronique de puissance et le véhicule de demain : optimisation d'un convertisseur 42V-14V sous des contraintes d'encombrement, de rendement, de compatibilité électromagnétique et thermique, Prop Elec'03, 19-20/03/2003, Aix en Provence, France

Larouci C., Didier J-P., Selvez M., Prado S., L'électronique dans l'automobile, Revue 3EI, N°33, Juin 2003

Sagot B., Approche locale / approche système en simulation numérique, Conférence Conception et optimisation des process industriels, 09/2003, Le Mans, France

Sagot B., Introduction du logiciel AMESim dans l'enseignement, Journée Universités AMESim, 11/2003, ENSPM, Rueil-Malmaison, France